Skip to main content

Threshold Ramps: Removing Doorway Barriers at Home

By MobilityLane Team | | 10 min read

Key Takeaways

  • Threshold ramps bridge small height changes at doorways, typically from 0.25 inches up to 6 inches
  • The ADA recommends a 1:12 slope ratio, meaning one inch of ramp length for every inch of height change
  • Materials include rubber, aluminum, and composite, each with different durability, weight, and cost profiles
  • Most threshold ramps require no permanent installation and can be placed, adjusted, or removed in minutes
  • Measuring both the height change and the available floor space on each side of the threshold is essential before purchasing

What Is a Threshold Ramp?

A threshold ramp is a small, portable or semi-permanent ramp that bridges a height change at a doorway. Unlike full-length wheelchair ramps that address multiple steps or significant elevation changes, threshold ramps handle the small but surprisingly problematic bumps where one floor surface meets another or where a door frame rises above the floor level.

These height changes are often only half an inch to two inches, but they create real barriers. A wheelchair caster can catch on a half-inch lip and stop forward motion completely. A walker’s front wheels can jam against a raised threshold, causing the user to pitch forward. A person shuffling with limited foot clearance can trip on a rise they cannot see or step over reliably.

Threshold ramps solve a specific, common problem cheaply and simply. They are one of the easiest home accessibility modifications you can make, often requiring no tools and no permanent changes to the home. For a full inventory of accessibility modifications worth considering, our home accessibility checklist is a good starting point.

Where Threshold Ramps Are Needed

Walk through any home with an eye toward small elevation changes and you will likely find several locations where a threshold ramp would help.

Interior doorways. Many homes have raised thresholds between rooms, especially where flooring materials change. The transition from tile to carpet, hardwood to tile, or any material to a concrete slab frequently creates a lip of 0.5 to 1.5 inches.

Exterior door thresholds. Front doors, back doors, and sliding glass doors almost always have a raised threshold to create a weather seal. These range from 0.5 to 2 inches or more and are among the most common barriers for wheelchair and scooter users.

Sliding door tracks. Patio and sliding doors have a bottom track that can be 0.75 to 1.5 inches high. This is especially problematic because the track is often narrow and metallic, creating a sharp edge that wheels can catch on.

Garage-to-house transitions. The step from a garage slab to the house interior is often 2 to 6 inches, technically at the upper end of what a threshold ramp can handle. Larger transitions may need a modular ramp system, which is covered in our wheelchair ramp slope and ADA guidelines guide.

Bathroom entries. Bathrooms sometimes have raised thresholds to contain water, creating a barrier for walkers and wheelchairs exactly where safe access matters most.

Types of Threshold Ramps

Rubber Threshold Ramps

Rubber ramps are the most common type for indoor use. They are made from dense, recycled rubber, typically in wedge or modular shapes. Their weight (they are heavy for their size) keeps them in place without adhesive, and the rubber surface provides excellent traction even when wet.

Rubber ramps work best for height changes up to about 2 inches. They are easy to trim to fit doorway widths and can be used on carpet, tile, wood, or concrete. The main limitation is that they can shift on smooth floors under repeated heavy wheelchair traffic, though most models include a non-slip bottom surface.

Cost typically ranges from $20 to $80 depending on height and width.

Aluminum Threshold Ramps

Aluminum ramps are lighter, thinner, and stronger than rubber for the same height capacity. They handle height changes from 1 to 6 inches and are especially common for exterior doorways where weather resistance matters. Aluminum does not rot, warp, or degrade in sunlight.

Most aluminum threshold ramps have a raised, perforated, or textured surface for traction. Some include side rails or edge guards to prevent wheels from rolling off. They are typically secured with screws or adhesive strips, making them semi-permanent installations.

Cost ranges from $40 to $200 depending on size and features. Aluminum ramps are the best choice when the height change exceeds 2 inches or when the ramp will be exposed to weather.

Composite and Fiberglass Ramps

Composite ramps split the difference between rubber and aluminum. They are lighter than rubber, more weather-resistant than basic rubber, and available in colors that blend with flooring. Some composite ramps are designed specifically for sliding door tracks, with contoured bottoms that fit over the track without permanently modifying it.

These are less common than rubber or aluminum options and tend to cost slightly more, typically $50 to $150.

Folding and Portable Ramps

For height changes above 3 to 4 inches, portable folding ramps provide a compact solution that can be set up and removed as needed. These are essentially miniature versions of full-length portable ramps, designed to bridge a single step rather than a flight of stairs. They are useful for renters who cannot make permanent modifications or for people who need ramp access at multiple doorways but do not want a ramp at every one.

Sizing a Threshold Ramp

Getting the right size requires two measurements: the height of the threshold and the available floor space.

Measuring the Height

Use a ruler or tape measure to find the exact height of the barrier. Measure at the tallest point. If the threshold is not uniform (for example, if it is beveled on one side), measure the maximum height the wheels must traverse.

For doorways where two different floor levels meet, measure the difference between the higher surface and the lower surface. This is the rise that the ramp must accommodate.

Calculating the Length

The ADA recommends a maximum slope of 1:12 for wheelchair ramps. This means the ramp should be at least 12 inches long for every 1 inch of height. A 1-inch threshold needs at least a 12-inch ramp. A 2-inch threshold needs at least a 24-inch ramp.

For power wheelchairs and mobility scooters, a 1:12 slope is manageable but can feel steep when loaded. A gentler slope of 1:16 or even 1:20 is more comfortable if floor space allows.

For manual wheelchair users, the slope matters even more because they are providing their own power. A person pushing a manual wheelchair up a short ramp may find 1:12 difficult without assistance. If the user has limited upper body strength, aim for 1:16 or gentler.

Checking Floor Space

A threshold ramp needs flat floor space on both the approach and landing sides. If the ramp leads into a small bathroom where the door opens inward, there may not be enough room for the ramp plus the wheelchair plus the door swing. Measure the clear floor area on both sides of the doorway before purchasing.

Installation Methods

No-Install Placement

Most rubber and some composite threshold ramps simply sit on the floor. Their weight and friction hold them in place. This works well for indoor applications on non-smooth surfaces. Check periodically that the ramp has not shifted, especially in high-traffic areas.

Adhesive Installation

For ramps that tend to shift, double-sided carpet tape or construction adhesive can secure them to the floor. This is semi-permanent: it holds the ramp firmly but allows removal with some effort. Adhesive works well on tile, concrete, and vinyl but can damage hardwood finishes when removed.

Screw-Down Installation

Aluminum and some composite ramps include pre-drilled holes for screw-down installation. This is the most secure method and is recommended for exterior applications where rain, snow, or temperature changes could shift the ramp. Use stainless steel screws to prevent rust.

Screw-down installation creates permanent holes in the threshold or floor, so this is not ideal for renters unless the landlord approves. It is, however, the safest option for ramps that support heavy power wheelchairs or scooters.

Threshold Ramps vs Full-Length Ramps

Threshold ramps and full-length ramps solve different problems, and confusion between them leads to poor purchasing decisions.

Threshold ramps handle height changes up to about 6 inches at doorways and floor transitions. They are small, relatively inexpensive, and often require no installation. They do not have handrails.

Full-length ramps handle larger elevation changes, such as porch steps, deck access, or building entries. They require more planning, more space, and often professional installation. Most include handrails and edge protection. Our wheelchair ramp slope guide covers the full-length ramp planning process in detail.

If the barrier at your doorway is more than 6 inches or involves a full step (typically 7 to 8 inches), you are in full-length ramp territory and should plan accordingly.

Funding and Coverage

Threshold ramps are among the most affordable accessibility modifications, but coverage is still worth exploring if you are making multiple home modifications.

Medicare generally does not cover threshold ramps. However, Medicaid home and community-based services (HCBS) waivers in many states do cover home modifications including ramps. The specifics vary significantly by state. Our guide to Medicaid mobility equipment coverage explains how these waivers work and how to apply.

VA benefits may cover threshold ramps as part of a home modification for eligible veterans, particularly through the Home Improvements and Structural Alterations (HISA) grant program.

Some Area Agencies on Aging and community nonprofits run home modification programs that include small ramp installations at no cost. Contact your local Area Agency on Aging to ask about available programs in your area.

Maintenance and Safety Checks

Threshold ramps require minimal maintenance but should be checked regularly.

Monthly checks. Verify the ramp has not shifted from its intended position. Test that adhesive or screws are still secure. Look for cracks in rubber ramps or dents in aluminum ramps that could catch wheels.

After weather events. Exterior ramps can shift in heavy rain or freeze-thaw cycles. Check alignment and re-secure if needed.

Surface traction. Clean the ramp surface periodically to prevent buildup of dirt, soap residue, or algae (for outdoor ramps) that reduces traction. A mild detergent and stiff brush are sufficient for most cleaning.

Replacement triggers. Replace a rubber ramp if it develops cracks, loses its shape, or compresses unevenly under weight. Replace an aluminum ramp if the surface texture wears smooth or if dents create an uneven surface.

FAQ

What height threshold requires a ramp for wheelchair access?

Any threshold over 0.5 inches is considered a barrier by most accessibility standards. The ADA specifies that changes in level up to 0.25 inches can be vertical, changes from 0.25 to 0.5 inches should be beveled at a 1:2 slope, and anything over 0.5 inches requires a ramp. In practice, many wheelchair users struggle with thresholds as low as 0.5 inches, especially those using manual chairs with small front casters.

Can you use a threshold ramp on carpet?

Yes, but with considerations. Rubber ramps grip carpet well and rarely shift. However, the ramp height needs to account for the carpet thickness on the approach side. If the carpet is thick, the effective height change the ramp must bridge is reduced. Also, the ramp’s bottom edge should sit flat against the carpet rather than bunching it up, which creates a secondary trip hazard.

Do threshold ramps work for walkers and rollators?

Absolutely. Threshold ramps benefit walker and rollator users as much as wheelchair users, sometimes more. Walkers with small front wheels catch on raised thresholds easily, and the resulting jolt can cause the user to lose their grip or balance. A smooth ramp transition eliminates this hazard. For rollators with larger wheels, even a small ramp makes passage smoother and reduces the jarring impact that can be painful for people with arthritis or joint problems.

Are threshold ramps allowed in rental apartments?

Under the Fair Housing Act, tenants with disabilities have the right to make reasonable modifications to their rental unit at their own expense, including installing threshold ramps. The landlord cannot refuse reasonable modifications but can require that permanent modifications be reversed when the tenant moves out. Portable rubber ramps that sit on the floor without adhesive or screws are not permanent modifications and generally do not require landlord approval at all.

ML

The MobilityLane Team

Written by a caregiver with 18+ years of experience supporting family members with chronic illness and mobility challenges, and medical training in mobility recovery. We research and write about mobility solutions to help people maintain independence and quality of life.

Learn more about us →

Stay Independent, Stay Informed

Get our weekly guide to mobility solutions, funding tips, and home safety resources delivered to your inbox.

Join 1,000+ caregivers and families. Unsubscribe anytime.

Related Guides